SuperStroke 3.0 to SuperStroke 1.0 Putter Grip How To & Review
SuperStroke putter grips have been growing in popularity on the tour for a few years now. A few months ago I decided to go with the SuperStroke Traxion Tour 3.0 Putter Grip and after using it a few time out on the course as well as on the putting green, I decided that the 3.0 was a bit too thick for my liking. For me the thicker grip didn’t have the feel I was hoping for, which is why I decided to change out the 3.0 with the SuperStroke Traxion Tour 1.0 Putter Grip. In the video below I will walk you through step-by-step on how to remove the larger putter grip and how to easily install the new much slimmer one.
- Purchase your new SuperStroke Putter Grip – Check Prices on Amazon Here
- Gather all needed supplies to install your SuperStroke Grip (Double Sided Tape, Grip Tape Solution, Hook Blades, Utility Knife, Mud Pan, Acetone, and a towel)
- Grab your putter
- Remove old grip by inserting hook blade and pulling away from you, peel back the grip. If you have any tension just reinsert the hook blade as you are peeling back the grip, it should come off pretty easily.
- Remove old double sided tape. Use utility knife with a regular blade to scrape off the tape, it should come off pretty easily. Wipe it down with the acetone to remove the old glue.
- Measure double sided tape to the length of your new putter grip and cut it
- Apply the double sided tape to your putter leaving a little over hang at the top of the putter shaft, tuck the tape into the hole at the top of the putter shaft.
- Wrap the tape around the putter shaft and remove the other side of the tape exposing the outer sticky part of the tape
- Pour your grip tape solution onto your new putter grip holding it over your mud pan while plugging the hole on the bottom of your grip with your finger.
- Once the grip is full with the solution pour it over the double sided tape, which you can just pour it or remove your finder from the hole in the bottom of your grip and let it flow out over the grip tape, either way will work fine. Either way hold it over your mud pan so you don’t make a mess and can save the tap solution as you can reuse it.
- Slide your new putter grip onto the shaft and over the double sided tape, it should slide on very easily.
- Once on, tap the end of the club on the floor a few times to make sure your golf grip is all the way on.
- Once on you will want to line up your grip with SuperStroke facing front and the gray line facing back (SuperStroke should face the hole and the gray strip should face away from the hole when holding your putter) Please note that you have plenty of time to line this up so there is no need to panic and rush through this. Test is out before setting it aside to dry.
- Wait 3-4 few hours (I usually wait 24 hours) to give it time to dry.
Installing your new SuperStroke putter grip at home without using a vise is no big deal and should only take a few minutes to complete. If you have any issues, comments, tips or tricks I would love to hear from you. I again appreciate you taking the time to stop by and I hope you found this post useful.
Here are the Links for everything you will need:
- SuperSroke Traxion Pistol Grip 1.0 Black/White/Blue: https://amzn.to/46EeOuO SuperSroke
- Traxion Pistol Grip 1.0 White/Grey/Red: https://amzn.to/3PPoixf SuperStroke Traxion Tour
- Golf Putter Grip 3.0 White/Grey/Red: https://amzn.to/46AJdKx
- Double Sided Golf GripTape: https://amzn.to/3JQoXee
- Grip Tape Activator Solution: https://amzn.to/3O4n3ZR
- Utility Knife: https://amzn.to/3XIsrVE
- Hook Blades: https://amzn.to/3D66B4Z
- 12″ Pan: https://amzn.to/44gru9G
+ENERGY Golf 